進口高壓電磁閥

詳細內容：進口高壓電磁閥 德國泰科閥門（國際）有限公司—廣州總代理 德國泰科閥門集團——中國指定供應商 GERMANY TEK VALVE COMPANY LIMITED 進口高壓電磁閥概述： 　　　進口高壓電磁閥分直動式和先導式兩種結構原理，領先設計的三維密封結構可靈活選配不同的密封材料，閥門可達零泄漏．高壓電磁閥有黃銅高壓電磁閥和不銹鋼高壓電磁閥． 　　進口高壓電磁閥安裝注意事項： 　　　　1、安裝前應參閱該產品的使用說明書,是否符合你的使用要求。 　　　　2、管路使用之前應沖洗干凈,介質不清潔的應安裝過濾器,以防止雜質妨礙電磁閥的正常工作。 　　3、長時間停用后的電磁閥,應排清凝結物后方便使用;拆洗時各零件要按順序放好再恢復原狀裝好。 　　　　4、電磁閥一般是單向工作的,不能反裝,閥上箭頭是管路流體的運動方向,必須保持一致。 　　　　5、電磁閥在結冰場所重新工作時應加熱處理,或設置保溫措施。 　　6、電磁閥安裝一般閥體水平,線圈垂直向上,有部分產品可以任意安裝,但在條件允許時最好垂直,以增長使用壽命。 　　7、電磁線圈引出線(接插件)連接好后,應確認是否牢固,聯接電器元件觸點不應抖動,松動將引起電磁閥不工作。連續要生產工作的電磁閥,最好采用旁路,便于檢修,不影響生產。 　　結構特點： 　　　　先導活塞式，最高壓力6.0M兆帕 空軍、海軍配套產品 　　　　設計緊湊，精巧美觀 溫升低，無噪音，零泄漏 　　動作響應迅速，高頻率 德國工藝，出口系列，品質可靠如介質含有雜質，閥前必須裝過濾器(濾網大于等于80目/厘米2)；且無凝固或晶體現象。 　　工作原理： 　　　　　常閉：當線圈通電時，先導閥芯吸合，先導孔打開，閥上腔卸壓，活塞靠下腔介質壓力推動，電磁閥打開；當線圈斷電時，先導閥芯靠彈簧復位，先導孔關閉，閥上腔由活塞節流孔增壓和復位彈簧的推力，電磁閥關閉。 　　　　　常開：當線圈通電時，先導孔關閉，閥上腔由活塞節流孔增壓和復位彈簧的推力，電磁閥關閉。當線圈斷電時，先導閥芯靠彈簧復位，先導孔打開，閥上腔卸壓，活塞靠下腔介質壓力推動，電磁閥打開。 　　主要技術參數： 　　　　◆閥體材質：不銹鋼。 　　　　◆適用介質：水、氣、油、蒸汽、燃?xì)�、腐蝕流體等。 　　　　◆溫度范圍：-100—+200℃。 　　　　◆介質粘度：小于50C St(大于時需定制）。 　　　　◆防護性能：防水、防爆（Exd IICT5)、防腐。 　　　　◆接線方式：接線座式；引線式；插頭式。 　　　　◆控制方式：常開、常閉。 　　　　◆電源電壓: DC12—127V; AC36—380V。 　　　　◆連接方式：內螺紋、法蘭（外螺紋和特殊接口可定做或加轉接頭）。 　　　　◆泄 漏 量：零。 　　German TEK Valves (International) Co., Ltd. - Guangzhou distributor 　　German TEK Valve Group - China designated supplier 　　GERMANY TEK VALVE COMPANY LIMITED 　　Imported high-pressure solenoid valve overview: 　　Imports of high-voltage direct-acting solenoid valve and pilot two structural principles, leading a three-dimensional design of flexible sealing structure matching different sealing materials, valves can reach zero leakage. High pressure solenoid valve solenoid valve with brass and stainless steel high-pressure solenoid valve. 　　Imported high-pressure solenoid valve installation considerations: 　　1, the installation should refer to the product manual, whether it meets your requirements. 　　2, the pipeline should be rinsed before use, the media should be installed dirty filter to prevent impurities interfere with the normal operation of the solenoid valve. 　　3, for a long time after the closure of the solenoid valve should be flushed after coagulation easy to use; washable according to the order of the parts when put away again restitution installed. 　　4, the solenoid valves are generally one-way working, is not reversed, the valve fluid line arrows the direction of movement must be consistent. 　　5, the solenoid valve should be back to work on icy places heat treatment, or set the insulation measures. 　　6, the solenoid valve is mounted generally horizontal body coil vertically upward, some products can be arbitrarily installed, but when conditions permit, preferably perpendicular, to increase service life. 　　7, the electromagnetic coil lead wire (connector) connected, should confirm whether the firm, the coupling of electrical components should contact jitter loose will cause the solenoid valve does not work. Continuous work to produce an electromagnetic valve, preferably bypass, ease of maintenance, without affecting production. 　　Structural features: 　　Pilot diaphragm, the maximum pressure 6.0M MPa Air Force, Navy ancillary products 　　Compact design, exquisite appearance, low temperature, no noise, zero leakage 　　Action responsive, high-frequency German technology, export series, reliable quality such as media containing impurities, the valve must be installed before the filter (the filter is greater than or equal to 80 mesh / cm 2); without solidification or crystal phenomenon. 　　How it works: 　　NC: When the coil is energized, the pilot spool pull, pilot hole opened, pressure relief valve chamber, the piston on the lower chamber medium pressure to promote, solenoid valve opens; When the coil is de-energized, the pilot valve by spring return, pilot hole is closed, the valve chamber and pressurized by a piston orifice and the return spring force, the electromagnetic valve is closed. 　　Normally open: When the coil is energized, the pilot hole is closed, the valve chamber and pressurized by the piston return spring throttle thrust, the solenoid valve closes. When the coil is de-energized, the pilot valve by spring return, pilot hole opened, pressure relief valve chamber, the piston on the lower chamber medium pressure to promote, the solenoid valve opens. 　　The main technical parameters: 　　◆ Body material: Stainless steel. 　　◆ Applicable medium: water, gas, oil, steam, gas, corrosive fluids. 　　◆ Temperature range: -100 - 200 ℃. 　　◆ Medium viscosity: less than 50C St (greater than to be customized). 　　◆ Protection Performance: waterproof, explosion-proof (Exd IICT5), antiseptic. 　　◆ Wiring: Terminal Block type; Leaded; plug-in. 　　◆ Control: Normally open, normally closed. 　　◆ Power supply voltage: DC12-127V; AC36-380V. 　　◆ Connection: thread, flange (male and special interfaces or add custom adapter). 　　◆ Leakage: Zero. 進口高壓電磁閥